SteamEraa India Private Limited is an Indian manufacturing company specializing in steam engineering products, industrial valves, and innovative solutions for efficient steam management.

Contact Info
Location

Near Indian Tools, Block - J178/1, MIDC, Block Sector: MIDC, Bhosari, Pune - 411026, Maharashtra, India

img
imgWelcome To

Steam System Solutions for Industrial Efficiency

SteamEraa India Pvt Ltd is India's leading steam system company specializing in boiler efficiency, steam distribution, condensate recovery and turnkey piping solutions. We help Pharma, Food, Textile and Chemical industries save 15-25% energy.

Optimal Performance Enhanced Safety Proven Energy Conservation

Efficient Steam, Greener Future. From concept to commissioning, we are your trusted partner for efficient steam.

0%

Average increase in sales
for our clients

849K+

Between Organization’s Managing

Our Steam Engineering Services

Comprehensive steam system audits, optimization, recovery, engineering, training and improvement projects.

01

Steam Generation Optimization

"Optimize boiler performance for maximum efficiency & fuel savings"

What We Do

Boiler is 70% of your steam system energy cost. We check how efficiently your boiler is converting fuel to steam.

Target efficiency: 85-90% for biomass/coal, 90-95% for gas/oil.

Our Checks

  • Boiler efficiency test — Direct method and Indirect method
  • Blowdown percentage — TDS control and blowdown heat recovery (Flash vessel + Heat exchanger)
  • Feed water temperature — Target 85-95°C, Deaerator performance, Economizer approach
  • Fuel analysis — GCV, Moisture, Unburnt in ash
  • Boiler loading — Optimum 70-85%, avoid low load <50% or overloading
02

Efficient Steam Distribution

"Minimize heat loss & pressure drop across distribution networks"

What We Do

Steam distribution is the highway of steam from boiler to process. 10-15% energy is lost here via leaks, poor insulation, wrong pipe sizing, faulty traps and PRV issues.

Our Checks

  • Steam pipe sizing — Superheated 40-60 m/s, Saturated 20-40 m/s, Wet 10-20 m/s; pressure drop <10%
  • Insulation survey — Bare surfaces, Valves, Flanges, PRV stations, heat loss in kcal/h & Rs/year
  • Steam trap audit — Thermal Imager Camera + Temperature Gun, trap failure % (Typical 15-30% fail), live steam loss kg/h
  • Steam leak audit — Leak quantification (1 no 3mm hole = 30 kg/h = Rs 3L/year), Thermal imaging
  • PRV station — Pressure reduction efficiency, Desuperheater, Dryness fraction
  • Pipe accessories — Pipe supports, Expansion loops, Drains, Air vents
03

Maximizing Steam Utilization

"Enhance steam use across processes to improve productivity"

What We Do

At process equipment (heat exchangers, reactors, dryers, vulcanizers etc.), steam must give its latent heat efficiently. Poor utilization means high batch time, low productivity and high steam kg/kg product.

Our Checks

  • Process heat balance — Steam in vs Product out, LMTD, Heat transfer coefficient (U value)
  • Control valve performance — Hunting, Oversizing, Manual bypass open (big wastage), Leakage
  • Steam pressure vs Temperature vs Batch time — Is higher pressure actually helping?
  • Condensate removal — Is process waterlogged? Thermostatic vs Float trap selection
  • Dryness fraction at process — Wet steam = Low heat content
  • Steam consumption per ton benchmarking — vs Best-in-class
04

Condensate Recovery and Management

"Recover and reuse condensate to reduce water & energy costs"

What We Do

Condensate is distilled hot water (80-90°C). Every 6°C rise in feed water = 1% fuel saving. Most plants recover only 40-50%; target is >80%. Flash steam is also wasted.

Our Checks

  • Condensate recovery % — Actual vs Target; where is condensate going to drain?
  • Flash steam recovery — Flash % calculation (Example: 8 bar to 2 bar = 10% flash), Flash vessel sizing & utilization
  • Condensate pump performance — Cavitation (NPSH), Mechanical vs Electrical pump, Leak
  • Condensate line sizing — Back pressure, Water hammer, Two-phase flow
  • Condensate contamination — Oil, Process chemical, pH, TDS — Is it reusable?
  • Condensate tank — Insulation, Venting (big steam plume = loss), Level control, Make-up water cost
05

Turnkey Piping Solutions

"P&ID — Piping & Instrumentation Drawing"

End-to-End Piping Solutions

End-to-end design, installation and modification of steam piping systems.

Scope of Work

  • P&ID preparation — AutoCAD / E-Plan
  • Line sizing — As per ASME B31.1
  • Isometric drawings
  • Line list preparation
  • Valve list preparation
  • Steam trap list preparation
06

Energy Conservation Training

"Customized training on steam energy saving"

Training Details

  • Audience — Operators, engineers and managers
  • Duration — 4 Hours to 1 Day
  • Mode — At your plant or online

We Cover

  • Boiler efficiency optimization
  • Steam distribution — Pipe sizing, Insulation, Leaks, Traps, PRV
  • Process utilization
  • Condensate & flash recovery (Section 4 — 1000L tank — Best ROI)
  • Instrumentation & Automation
  • Troubleshooting — Water hammer, Trap failure, High fuel

You Get

  • Training kit + Certificate
  • Lifetime calculator access
  • 1 month WhatsApp support
  • Action plan with ROI
Result: Team can identify wastage & save 10-20% fuel — Typical Rs 15-25L/year for 5 TPH boiler.
07

Steam System Improvement Project

"From audit to implementation — We don't just suggest, we implement and show savings on flow meter."

Projects We Execute

  • Steam trap replacement and management system (60% failure to <5% failure)
  • Condensate recovery system installation (pump + piping)
  • Flash steam recovery vessel installation
  • Boiler blowdown heat recovery
  • Proper pipe sizing and pressure reduction station
  • Insulation of bare valves, flanges and heat exchangers
  • Auto pump traps for paper machine and textile machine where stall conditions occur
whatsapp